SQUAWK DIRTY TO ME
8 mode zero-delay feedback stereo VCF with Meta CV scan
Simple and effective 6hp stereo VCF
96 khz 16 bits audio I/O with 32 bits internal processing
8 filter modes available with meta CV scanning, famous zero-delay feedback Grand Terminal filters: 24DB/OCT TRANSISTOR LADDER, MS-20 12DB/OCT, 12DB/OCT LOW PASS GATE, 12DB/OCT RESONANT LOW PASS GATE, 12DB/OCT DJ ISOLATOR BIPOLAR VARIABLE FILTER, 12DB/OCT HIGH PASS STATE VARIABLE FILTER, 12DB/OCT BAND PASS STATE VARIABLE FILTER, COMB FILTER / RESONATOR.
Additional hi-pass filter in series quickly cuts the boomy low end.
Stereo image widener with adjustable all pass filter delay on Right output.
Built in post filter VCA for compact voice setup.
Power consumption:
120 mA +12V
15 mA -12V
0 mA 5V
Dimensions:
6 HP
30 mm deep
Modulargrid: BLACK
Manual: HERE
Firmware Update: LATEST RELEASE V4 ‘TOTAL NIGHTMARE’ 20-MAY-2021
Want to pimp up your module’s look? Check its faceplate replacement & knobs
FAQ:
My signal sounds very stereo enhanced even though I only use a mono input. There is a built-in delay of the right channel 2. Your can adjust it from being fully zero or up to 0.5-0.7 seconds maximum. Middle values create stereo enhance - adjust by taste. Do this by pressing the ‘MODE’ button for 2.5 seconds an then turn the volume knob to set the delay desired.
How to update. Check this video.
Rainbow cable pinout. Side red/brown pair of pins always correspond to -12V similar as with typical gray ribbon cable.
8 mode zero-delay feedback stereo VCF with Meta CV scan
Simple and effective 6hp stereo VCF
96 khz 16 bits audio I/O with 32 bits internal processing
8 filter modes available with meta CV scanning, famous zero-delay feedback Grand Terminal filters: 24DB/OCT TRANSISTOR LADDER, MS-20 12DB/OCT, 12DB/OCT LOW PASS GATE, 12DB/OCT RESONANT LOW PASS GATE, 12DB/OCT DJ ISOLATOR BIPOLAR VARIABLE FILTER, 12DB/OCT HIGH PASS STATE VARIABLE FILTER, 12DB/OCT BAND PASS STATE VARIABLE FILTER, COMB FILTER / RESONATOR.
Additional hi-pass filter in series quickly cuts the boomy low end.
Stereo image widener with adjustable all pass filter delay on Right output.
Built in post filter VCA for compact voice setup.
Power consumption:
120 mA +12V
15 mA -12V
0 mA 5V
Dimensions:
6 HP
30 mm deep
Modulargrid: BLACK
Manual: HERE
Firmware Update: LATEST RELEASE V4 ‘TOTAL NIGHTMARE’ 20-MAY-2021
Want to pimp up your module’s look? Check its faceplate replacement & knobs
FAQ:
My signal sounds very stereo enhanced even though I only use a mono input. There is a built-in delay of the right channel 2. Your can adjust it from being fully zero or up to 0.5-0.7 seconds maximum. Middle values create stereo enhance - adjust by taste. Do this by pressing the ‘MODE’ button for 2.5 seconds an then turn the volume knob to set the delay desired.
How to update. Check this video.
Rainbow cable pinout. Side red/brown pair of pins always correspond to -12V similar as with typical gray ribbon cable.
8 mode zero-delay feedback stereo VCF with Meta CV scan
Simple and effective 6hp stereo VCF
96 khz 16 bits audio I/O with 32 bits internal processing
8 filter modes available with meta CV scanning, famous zero-delay feedback Grand Terminal filters: 24DB/OCT TRANSISTOR LADDER, MS-20 12DB/OCT, 12DB/OCT LOW PASS GATE, 12DB/OCT RESONANT LOW PASS GATE, 12DB/OCT DJ ISOLATOR BIPOLAR VARIABLE FILTER, 12DB/OCT HIGH PASS STATE VARIABLE FILTER, 12DB/OCT BAND PASS STATE VARIABLE FILTER, COMB FILTER / RESONATOR.
Additional hi-pass filter in series quickly cuts the boomy low end.
Stereo image widener with adjustable all pass filter delay on Right output.
Built in post filter VCA for compact voice setup.
Power consumption:
120 mA +12V
15 mA -12V
0 mA 5V
Dimensions:
6 HP
30 mm deep
Modulargrid: BLACK
Manual: HERE
Firmware Update: LATEST RELEASE V4 ‘TOTAL NIGHTMARE’ 20-MAY-2021
Want to pimp up your module’s look? Check its faceplate replacement & knobs
FAQ:
My signal sounds very stereo enhanced even though I only use a mono input. There is a built-in delay of the right channel 2. Your can adjust it from being fully zero or up to 0.5-0.7 seconds maximum. Middle values create stereo enhance - adjust by taste. Do this by pressing the ‘MODE’ button for 2.5 seconds an then turn the volume knob to set the delay desired.
How to update. Check this video.
Rainbow cable pinout. Side red/brown pair of pins always correspond to -12V similar as with typical gray ribbon cable.
